Merry Christmas from Airmax :)

The Airmax family would like to wish everyone a very merry and safe Christmas and Holiday season. May all your dreams come true.

Thank you for being our valued customer and friend!!

New Testimomial For Airmax :)

December 22, 2011
by Bill Hall
December 22, 2011
Reva, As a General Contractor, I know the value of customer service. Airmax once again has surpassed my expectations in service and satisfaction! Your unsolicited offer to follow up on the air unit you installed back in August, service the heating system and free of charge was a welcome breath of fresh air. Not only will I continue to have Airmax continue to service my heat and air conditioning, but I will recommend your services to others. Bobby is a super nice and professional technician. Thank You for caring about me and my family.
Regards,
Bill Hall
Sachse, TX

Brrrr .. It's cold outside !! :)

Your friends here at Airmax, would like to remind you on this "cold" December morning to keep in mind; now is the time to think about a fall/winter tune-up for your heating units.

Heating Season Planned Maintenance Factory trained Service Technicians provide the following:
14 point precision tune-up, cleaning and safety inspection services.

Clean or Replace Filters: A dirty filter will reduce the air flow, resulting in inefficient heating, reduced heating capacity, poor air filtration, and higher heating costs.

Adjust and Clean Blower Components: Proper adjustment and cleanliness of blower and components is necessary for adequate air flow to ensure your furnace can deliver maximum heating capacity and efficiency.

Check and Test Safety Controls: Safety controls are essential for proper protection of the unit and your home or office, and will be adjusted to factory specifications

Monitor Furnace Cycle: Our trained Technician will assure that the heating system is cycling on and off properly and that controls are calibrated to factory specifications.

Adjust Gas Pressure: Proper gas pressure to the burners will ensure the most efficient and safe burner operation and reduces energy costs.

Clean Heat Exchanger and Burners: Dirty heat exchangers and burners reduce the heating efficiency and capacity of your furnace.

Adjust Heat Anticipator Settings: The heat anticipation in your thermostat determines how often your furnace cycles and will affect the cost of operation, as well as the comfort level in your home or office.

Monitor Flue Draft for Safe Operation: An obstructed flue will cause products of combustion to enter your home or office.

Thoroughly Check for Cracked Heat Exchanger: As your furnace gets older, there is a real danger of cracks developing in the heat exchanger. These cracks can allow dangerous products of combustion (including carbon monoxide) to enter the fresh air of your home or office and endanger your safety. We will thoroughly inspect your heating system visually and electronically to determine if this hazard is evident.

Check and Adjust Pilot Operation: A properly adjusted pilot will assure that your furnace will start reliably all winter. Lubricate All Moving Parts Where Applicable: Poor lubrication causes drag in the motor and drive shaft, thereby – requiring more electricity to overcome resistance. This condition will cause early motor or bearing failure.

Check and Tighten All Loose Electrical Connections: Loose electrical connections are a common source of equipment failure.

Monitor Voltage and Amperage Draw on all Motors: Motors are designed to operate at standard voltage and amperage draw. By measuring amperage draw, problems can be identified before the unit fails.

Clean and Adjust Thermostat
Call us today and take advantage of our special pricing. 972.382.3200 To ensure even temperature control for your home or office.

 

 

 

Energy Saving Tips

 

Tip 1 - Set your thermostat as low as is comfortable in the winter and as high as is comfortable in the summer.

Tip 2 - Don't set your thermostat at a colder setting than normal when you turn on your air conditioner. It will not cool your home any faster and could result in excessive cooling and, therefore, unnecessary expense.

Tip 3 - Don't place lamps or TV sets near your air-conditioning thermostat. The thermostat senses heat from these appliances, which can cause the air conditioner to run longer than necessary.

Tip 4 - Clean or replace filters on furnaces once a month or as needed.

Tip 5 - Clean warm-air registers, baseboard heaters, and radiators as needed; make sure they're not blocked by furniture, carpeting, or drapes.

Tip 6 - During the heating season, keep the draperies and shades on your south-facing windows open during the day to allow the sunlight to enter your home and closed at night to reduce the chill you may feel from cold windows.                

Tip 7 - During the cooling season, keep the window coverings closed during the day to prevent solar gain.

Tip 8  - Have a preventive maintenance check and cleaning twice a year. Once during the heating season and once during the cooling season.

New Customer Review

It is a great value to be a Diamond customer.  Your technician Adriel arrived in less than two hours of our phone call, and had us back in service in 30.minutes.  He was professional in conduct and appearance.  Great job!
 

T. James Buchanan
Dallas, Texas

Time for a winter check-up on your heating units

Now is the right time to schedule a check-up on your heating units:

We offer 2 great yearly contract options & a one time safety inspection option. Below you will find pricing & the  benefits of each option.

Diamond Contract Option
239.00 for 1st unit & $100.00 each additional unit
Monthly option is $31.34 for 1 unit & $8.50 each additional unit

Contract Includes:
1 Heating tune-up per year
1 A/C tune-up per year
27 point inspection
2 free service calls per year (exclusive to Diamond)
No overtime charges (exclusive to Diamond)
5lbs of free refrigerant (exclusive to Diamond)
15% preferred customer pricing
Clean heat exchanger and burners (exclusive to Diamond)
Clean evaporator coil (exclusive to Diamond)
Clean condenser coil (exclusive to Diamond)

Plus Contract option:
$99.00 per year, per unit

Contract Includes:
1 Heating tune-up per year
1 A/C tune-up per year
27 point inspection
Replace or clean standard 1" filters only (additional cost for special sizes)
Provided estimate of any needed repairs found during inspection
10% Discount for all repair parts and labor
Priority scheduling Mon-Fri 8am-5pm
Inspect and clean condenser coils as needed
Inspect and clean evaporator coils as needed in place

One-time Option:
$49.95 per unit

Includes:
27 point safety inspection
change standard filters
Heating season inspection for all options include:
Clean or replace air filters with specification to option
Lubricate all moving parts (where applicable)
Inspect and tighten electrical connections
Adjust gas pressure as necessary
Inspect pilot operation- adjust as needed
Monitor flue draft for safe operation
Inspect and test safety controls
Inspect heat anticipator settings
Inspect thermostats operations
Clean heat exchanger and burners  (Diamond option only)

Benefits for contract options include:
Priority customer
Inflation protection
Agreement is transferable
24-hour emergency service
No overtime charge
Improved efficiency
Extended equipment life
Improved safety
Improved capacity

New Testimonial 11/29/2011 :)

November 29, 2011
by Andre" P.
You were on time and did your work in a professional manner and you love dogs. Your firm is one of the best we have had service contracts with in the past.Keep up the good work.
Andre" P.